1.5kw ER20 square air cooled spindle

1.5kw ER20 square air cooled spindle

: In stock

: 1.5KW Sqaure spindle

: GoCNC

Regular price R 7,500.00 Sale

Size: 139x110x95mm Speed Ways: Through 3-phase output inverter and adjust the inverter frequency to change the spindle speed. Cooling: Air Cooling Power Interface: Optional 5 pins waterproof air plug. The air plug marked "1...

R 7,500.00

主轴+变频器详情页_04

主轴+变频器详情页_05

主轴+变频器详情页_06

  • Size: 139x110x95mm

  • Speed Ways: Through 3-phase output inverter and adjust the inverter frequency to change the spindle speed.

  • Cooling: Air Cooling

  • Power Interface: Optional 5 pins waterproof air plug. The air plug marked "1 ","2"," 3"," 4" "5" "GND". "1 ","2 ","3" were connected to inverter (U, V, W), "GND" connected inverter ground.

  • Power: 1.5kw

  • Voltage: 220v/380V

  • Current: 6.5A

  • Frequency: 0-300Hz

  • Speed: 0-18000rpm

  • Runout Off: Less than 0.01m

  • Bearing Type: 2 x 7005 P4 DT & 2 x 7002 P4 DT

  • 4pcs fully sealed angular contact bearings

  • Collet: ER20

  • Clip Knife diameter: 13mm,12mm,12.7mm,11mm,10mm,9mm,8mm,7mm, 6.35mm,6mm, 5mm, 4mm, 3.175mm, 3mm, 2mm, 1mm (standard 6mm)

  • Air Cooling ER20 collet chunk

  • With Mounting Flange

  • Grease Lubrication

  • Main Application: Engrave for wood,bamboo,normal PCB,PVC,PMMA,plastic,bamboo,duotone board(ABS)and etc nonmetal,also can engrave on gold,silver,copper,aluminium,Pb etc soft metal surface working.

 

主轴+变频器详情页_08

 

-1_05

主轴+变频器详情页_10

  • Bearing is P4 grade,2×7005C P4 DT & 2 x 7002C P4 DT,increase the spindle life.

  • Spindle collet chunk ER20 type, accept 1-13mm diameter tools, bigger than ER11 and ER16.

  • High precision,runout off less than 0.01mm.Coaxial degree less than 0.0025mm

  • Shipment within four days,there is no fake tracking number,make sure that you receive time.

  • We are the spindle manufacturer,we offer only best quality and best price to you.

 

 

主轴+变频器详情页_11主轴+变频器详情页_12

  • Power: 1.5kw

  • Input Voltage: 220v (±20%)

  • Input Phase: 1 or 3 phase

  • Input Frequency: 50-60Hz (±5Hz)

  • Output Voltage: 220v

  • Output Phase: 3 phase

  • Output Current: 7A

  • Output Frequency: 0-1000Hz

  • Control Method: V/F control; Open-loop flux vector control

主轴+变频器详情页_14主轴+变频器详情页_15

◆Two speed control modes: no PG vector control (SVC), V/F control

◆ No PG vector control (SVC): starting torque 0.5Hz up to 150%

◆ 8-stage simple PLC function, multi-speed control and PID control

◆ Support multiple frequency settings: digital setting, analog setting, PID setting, RS485 communication setting

◆ I/O terminals can be freely programmed to combine multiple working modes according to user needs.

◆ With jump frequency control function, it can effectively suppress mechanical resonance and make the system more stable and reliable.

◆ With instantaneous power-down retention function, it can avoid the impact of production due to instantaneous power failure

◆ With over torque and under torque detection

◆ Automatic voltage adjustment function to effectively solve the low frequency oscillation problem of high power motor

◆ Provide a variety of fault protection functions: over-current, over-voltage, under-voltage, over-heat, overload, lack of equal real-time monitoring and protection to ensure safe operation

 

主轴+变频器详情页_17

winding machine,mixer, extruder,slitter,winder,compressor,ventilator,pump,grinder,conveyor,elevator,centrifuger and other speed control machines.

 

主轴+变频器详情页_42

DO NOT set up the inverter by yourself if you don't know how to, or it will make both the spindle and inverter burn easily.

Please contact us, we have manuals, videos and pictures to help you.

 

主轴+变频器详情页_19主轴+变频器详情页_20主轴+变频器详情页_21主轴+变频器详情页_22主轴+变频器详情页_23主轴+变频器详情页_24主轴+变频器详情页_25

主轴+变频器详情页_28

  • Spindle working environment temperature is usually -10  ~ 40 .
  • Before installing the first electric spindle axis head turned by hand, should feel flexible, non-blocking phenomenon.

 

主轴+变频器详情页_30

  • Spindle in the preservation and transportation, high-speed grease inside the bearing state will change, customers should be running at low speed for 30 minutes. 3000 rpm and then follow the poor increase, run 20 minutes each. Spindle and the inverter should be working together. The inverter's specifications and parameter settings need match spindles parameter.

  • Connect the inverter spindle, three-phase inverter power cord should be soldered in the plug 1 (U), 2 (V), 3 (W) feet, 4 feet for the ground. After the power is turned on, to observe whether the spindle rotation axis indicates the direction consistent. If inconsistency should be immediately shut down, replace the inverter and spindle connected two wires of three-phase power supply.

  • It should ensure that before use of water-cooled spindle, the cooling system is working properly. Every day before using the spindle must be running at low speed for 15-20 minutes. Clamping the cutters to spindle, collet nuts ,collets,cutters must be clean enough. Shank inserted into the collet must be greater than 15mm.

 

主轴+变频器详情页_30

主轴+变频器详情页_34

  • Water cooled spindle MUST be used with water pump. Otherwise the spindle will soon broken.

  • AC spindle motor MUST use with inverter. The power of inverter need equal or bigger than the spindle power. Before using,please set up the inverter parameters suitable for spindle. Otherwise the spindle and inverter will broken at once.

  • When you use the spindle,the noise is not same as always,please STOP the spindle at once. You may need to replace the spindle bearings.

 

主轴+变频器详情页_36

1. Cooling in different ways: water-cooled spindle motor is the use of the water cycle to cool the heat generated after the high-speed rotating spindle, spindle motor with fan-cooled approach to cooling.

  • 2. Noise: Water-cooled spindle motor is basically no noise, but the air-cooled spindle motor is very loud.

  • 3. Life aspects: Water-cooled spindle motor pay attention to maintenance, frequently changes the water or the use of industrial water coolers, air-cooled spindle fan mainly by the wind blowing the heat transferred to the heat sink, so as to achieve the cooling effect.

  • 4.If you need use for metal ,hard wood,granite,stone,you can choose metal spindle.Metal spindle much better than wood spindle.

主轴+变频器详情页_35主轴+变频器详情页_36

Returns Policy

You may return most new, unopened items within 30 days of delivery for a full refund. We'll also pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.).

You should expect to receive your refund within four weeks of giving your package to the return shipper, however, in many cases you will receive a refund more quickly. This time period includes the transit time for us to receive your return from the shipper (5 to 10 business days), the time it takes us to process your return once we receive it (3 to 5 business days), and the time it takes your bank to process our refund request (5 to 10 business days).

If you need to return an item, simply login to your account, view the order using the 'Complete Orders' link under the My Account menu and click the Return Item(s) button. We'll notify you via e-mail of your refund once we've received and processed the returned item.

Shipping

We can ship to virtually any address in the world. Note that there are restrictions on some products, and some products cannot be shipped to international destinations.

When you place an order, we will estimate shipping and delivery dates for you based on the availability of your items and the shipping options you choose. Depending on the shipping provider you choose, shipping date estimates may appear on the shipping quotes page.

Please also note that the shipping rates for many items we sell are weight-based. The weight of any such item can be found on its detail page. To reflect the policies of the shipping companies we use, all weights will be rounded up to the next full pound.